Industrial Label Thickness: Facestock vs. Finished Caliper

Specify label thickness clearly and compare supplier quotes with confidence. Learn the differences between facestock caliper, overlaminated builds and finished label thickness, including what to measure for recessed nameplates, cord labels and automatic applicators before approving samples.

Article6 min readTianyue Label Solutions

A buyer asks for a 50-micron label and receives two technically different quotations. One supplier measures the polyester face film. Another quotes the finished label off the liner. The values sound comparable until the part is installed in a recess or run through a dispenser. Write the measurement boundary beside every thickness and ask the supplier to identify whether the number is nominal, typical or a controlled acceptance limit.

Which thickness should I put on my drawing?

Think of a printed label as a stack. The facestock is the material you print on. If the supplier calls it 50 µm PET, that number describes the PET face in our material schedule. Adding a 25 µm protective film gives you 75 µm of face film plus protective film. The finished label will also have adhesive and may have coatings, so 75 µm is a layer subtotal. If your drawing says maximum installed thickness, ask for a measurement of the finished label with the release liner removed.

What you are designingThickness to specifyWhat to check
A flat nameplate with room around itFacestock thickness, plus the finish and adhesive separatelyCheck appearance, small text, and ease of placement on the actual housing.
A label that must sit flush in a recessMaximum finished thickness off the linerMeasure the applied build, including adhesive and any overlaminate, against the available depth.
A label wrapped around a cordFinished construction and the actual cord diameterCheck spring-back, edge lift and closure on the smallest cord in the range.
A roll for an automatic applicatorDelivered construction, liner and roll specificationRun a trial at normal speed. Check sensor detection, peel and feed.

If you are unsure which number to specify, send us the part drawing or a sample. Tell us where the label goes, how it is applied, and whether the limit is driven by clearance, handling or wear. We can discuss a single-film build and an overlaminated build and agree which thickness to measure before sampling.

Worked example: a nominal film value becomes a stack limit

Illustrative example.

Suppose a buyer compares two matte silver samples marked 50 micrometers. One sample has a thin clear overlaminate and another has a thicker protective film. Both can match a 50-micrometer base-film specification while sitting at different heights in a molded recess. Request the layer schedule and an off-liner sample for each. If the assembly also requires a limited web thickness for dispensing, request that measurement separately. Applying one acceptance limit to both numbers can reject good material or approve a label that interferes with the part.

At incoming inspection, state whether the test is on the smooth center or across printed or textured areas. Agree on the gauge and contact pressure, particularly for compressible builds. Record whether the result is a nominal calculation or a measured reading. If a specification lists a paper facestock by grams per square meter, keep that field separate and request an actual caliper where the stack matters. When materials are substituted, recheck the layer boundary and the installed fit even if the nominal face caliper matches.

For more guides in this series, see Selection, Materials & Adhesives.

Use facestock thickness as the standard data field

A specification for custom finished dimensions should list length and width separately from the material caliper. Use facestock thickness for the nominal thickness of the face material as defined on the supplier data sheet. In the TYLabel table, the stated base-film figure excludes adhesive and overlaminate. A drawing may separately call for the thickness of the finished label off the release liner. If the quote lists a range, state whether it describes alternative stock grades, a nominal dimension with tolerance, or an allowed range for the applied stack. A nominal value without a tolerance should remain a nominal value.

LINTEC industrial labelstock and overlaminate terminology Livasta labelstock and application surface information 3M durable label materials and print systems

Sample and measurement checklist

DecisionSend with the sample requestCheck before release
Base film specificationMaterial reference and facestock nominal caliper in micrometersCheck that both suppliers report the same film boundary and unit
Protective film specificationOverlaminate type and film caliper with bond detailsConfirm if its adhesive is included in the declared measurement
Installed stackRecess height, applied sample and measurement methodMeasure the finished label off the release liner with agreed pressure and sampling locations
Delivery stackLiner grade, web caliper and applicator constraintsTrial the delivered web and verify dispensing at operating speed
Thickness acceptanceNominal, permitted variation and signed inspection methodRecord which reading is used for supplier acceptance and incoming inspection

1. Base film specification

Ask whether the supplier's figure includes a topcoat. State 25 or 50 micrometers for nominal matte silver film rather than carrying a number sign into the English purchase order.

2. Protective film specification

Record overlaminate film and any lamination adhesive as distinct layers when stack height is critical. Require a plain-language measurement boundary for each line.

3. Installed stack

Measure off-liner samples at several agreed locations. Avoid comparing printed or embossed areas with an unprinted center unless the method calls for it.

4. Delivery stack

Include liner and release behavior when evaluating roll handling. Two materials with equal applied caliper can dispense differently with different liners.

5. Thickness acceptance

Set an agreed minimum, maximum or nominal target based on the application. Retain a reference reading and define how measurement variation will be handled.

Compare micrometers and mils

One mil is one thousandth of an inch, or exactly 25.4 micrometers. Nominal 25-micrometer film is approximately one mil, and nominal 50-micrometer film is approximately two mils. These are useful comparisons for reading supplier literature. Keep the units and nominal specification from the released document when setting acceptance limits. A buyer that rounds values at every step can accidentally create a narrow mismatch between quotes and inspection. If thickness is critical because a recess is shallow, specify the maximum applied stack directly and ask the supplier to declare any variation at print or laminate overlap.

Frequently asked questions

Does 50# silver PET include adhesive?

In the stated TYLabel matte silver film convention it describes nominal facestock only. Confirm the units and layer boundary on the quotation.

Can 80 grams per square meter be converted directly to micrometers?

No universal conversion applies. Basis weight describes mass per area, and caliper also depends on density, coatings and construction.

Request a technical review

Send TYLabel the information in the sample request table, along with the intended application, destination and expected order quantities. Ask for an engineering sample or a construction review against your current drawing. For a related application, see our transformer rating labels.

Read next in the TYLabel resource library. PET, PVC, Polyimide or Synthetic Film? Choose the Right Label Material.

Technical references

For reference, 25# and 50# matte silver PET in our material schedule mean nominal 25 and 50 µm facestock. The figures exclude adhesive and protective overlaminate.

WeChat — Amy

WeChat

Scan in WeChat, or open and save the image to scan from your phone.

Open QR Image